Franzen fire door

T-30
Allgemeine bauaufsichtliche Zulassung Nr. Z 6.20-1909, DIBt Berlin

Combinable with additional performance characteristics:

Smoke control according to DIN 18095 RS-1
Allgemeine bauaufsichtliche Zulassung Nr. Z 6.20-1909, DIBt Berlin

RC4 - classification report no. 22-5/15.119, PIV-Velbert
RC3 - classification report no. 22-4/15.117, PIV-Velbert
RC2 - classification report no. 45-47/22, PIV-Velbert
RC1 - classification report no. 212 24294, ift Rosenheim

according to DIN EN 1627 ff

up to R_W (C;C_tr) = 53 (-1;-5) dB

according to EN ISO 10140-1 / EN ISO 10140-2 / EN ISO 717

proof of airborne sound insulation for security doors
(measurement reports, test reports, expert opinions)

U_D-value ≥ 1.3 W/(m²K) according to EN ISO 10077-1

up to class 4 according to EN 12207 (up to 600 Pa)

up to 5.000 Pa according to DIN EN 12211

flush-mounted design FLAT

leaf thickness 68 mm to 69 mm - smooth double-walled
plate thickness 1.0 mm to 1.5 mm

• thin rebate design
  • optional thick rebate design
  • insulating insert
    • optional insulation inlet full-face glued and pressed with cover plate
      thus particularly plane and smooth door leaf

• frame-system "ZNG" with flush clipped in Thelesol® fire protection strips
• or
• frame-system "ZG"
• (see installation variants)

• corner frame
• optional enclosing frame
• optional block frame

with elastic rubber seal
(seal type depending on performance characteristic)

required for smoke control, acoustic performance, air tightness

• optional lowerable floor seal or
• sliding seal

glass dimensions and -form variable

minimum frieze width: 90 mm

• optional with intermediate glass inset bars
• optional with port-hole (ø approx. 450 mm clear view)
• optional in overhead / side panel

glass inset bars with concealed screw connection (for rectangular glass inset)

2/3-part KO door hinges
with patented easy-running bearings as easy running doors

• optional door hinge with 3D adjustment

• optional any approved handle set according to EN 1906 resp. EN 179
• optional panic bar handle or push bar according to EN 1125

for RC version: protective fitting DIN 18 257

single locking according to EN 12209, depending on version multi-point locking
profile cylinder prepared (cylinder on-site)
securing pins

• for version RC4: lock combination with triple locking
• optional panic locking according to EN 179 resp. EN 1125

door closer according to DIN EN 1154

• optional spring hinge for smaller doors / flaps
• optional hold-open system according to DIN EN 14637

• in masonry(thk ≥ 115 mm)
• in concrete(thk ≥ 100 mm)
• in aerated concrete(thk ≥ 150 mm)
• in mounting walls min. F30 (thk ≥ 100 mm)
• in encased steel columns(thk ≥ 100 mm)

• optional blunt installation in soffit
• optional installation on the wall plate
• approved for installation at great heights (installation not at floor level: height on one or both sides > 500 mm above ground level - e.g. as manhole door/flap) with lower fire and smoke seal - also thresholdless

mark of conformity - "Ü"
according to German conformity mark regulation

• lock control
• automated opening
• motor locks ( also in 3-way locking)
• powder coating in RAL colors
• prison cell doors (special locking and food flap)
• special solutions according to request and customer requirements