Franzen fire door class EI

Double-leaf fire resistance door EI₂ 60 / E60 / EW 60 (S_a/S₂₀₀)

marked

Combinable with additional performance characteristics:

S_a / S₂₀₀ tested according to EN 1634-3

RC4 - classification report no. 22-7/15.119, PIV-Velbert
RC3 - classification report no. 22-6/15.117, PIV-Velbert
RC2 - classification report no. 212 24303, ift Rosenheim
RC1 - classification report no. 212 24302, ift Rosenheim

according to DIN EN 1627 ff

up to R_W (C;C_tr) = 48 (-1;-5) dB

according to EN ISO 10140-1 / EN ISO 10140-2 / EN ISO 717

proof of airborne sound insulation for security doors
(measurement reports, test reports, expert opinions)

U_D-value ≥ 1.9 W/(m²K) according to EN ISO 10077-1

up to class 3 according to EN 12207 (up to 600 Pa)

up to class C4 (up to 2,000 Pa) according to EN 12210

up to class 3A according to EN 12208

up to 3.800 Pa according to DIN EN 12211

class 2 (d + e) according to EN 12219 (deflection)

hold-open device according to DIN EN 14637

flush-mounted design FLAT

leaf thickness 68 mm to 69 mm - smooth double-walled
plate thickness 1.0 mm to 1.5 mm

• thin rebate design
  • optional thick rebate design
  • insulating insert
    • optional insulation inlet full-face glued and pressed with cover plate
      thus particularly plane and smooth door leaf

• frame-system "ZNG" with flush clipped in Thelesol® fire protection strips
• (see installation variants)

• corner frame
• optional enclosing frame
• optional block frame

with elastic rubber seal
(seal type depending on performance characteristic)

required for smoke control, acoustic performance, air tightness

• optional lowerable floor seal or
• sliding seal

glass dimensions and -form variable
(rectangular glass inset max. 980 mm x 2,180 mm)

minimum frieze width: 130 mm

• optional with intermediate glass inset bars
• optional with port-hole (ø approx. 450 mm clear view)

glass inset bars with concealed screw connection (for rectangular glass inset)

per leaf 2/3-part KO door hinges
with patented easy-running bearings as easy running doors

• optional any approved handle set according to EN 1906 resp. EN 179
• optional panic bar handle or push bar according to EN 1125

for version RC: Protective fitting ES-1 up to ES-3

single locking according to EN 12209, depending on version multi-point locking
profile cylinder prepared (cylinder on-site)

internal snap bolt (locking upwards)
depending on version, with locking upwards and downwards (rebate shoot bolt, shoot bolt lock)

securing pins at both leafs

• optional panic locking according to EN 179 resp. EN 1125

both leafs with door closer according to DIN EN 1154 resp. EN 1155
with door closing sequence control according to EN1158

• in masonry(thk ≥ 115 mm)
• in concrete(thk ≥ 100 mm)
• in aerated concrete min. F90 (thk ≥ 150 mm)
• in mounting walls min. F90 (thk ≥ 100 mm)
• in encased steel columns min. F90 (thk ≥ 100 mm)

• optional blunt installation in soffit
• optional installation on the wall plate

marking for firedoors according to EN 16034

• lock control
• automated opening
• motor locks ( also in 3-way locking)
• powder coating in RAL colors
• prison cell doors (special locking and food flap)
• special solutions according to request and customer requirements